AS/NZS 1554.1:2004
Structural steel welding - Welding of steel structures
Specifies requirements for the welding of steel structures made up of combinations of steel plate, sheet or sections, including hollow sections and built-up sections, or castings and forgings. It is limited to the welding of steel parent material with a specified minimum yield strength not exceeding 500 MPa. It does not apply to oxyacetylene, friction, thermoset or resistance welding processes or to the welding of pressure vessels or pressure piping.
| Get this standard | Prices exclude GST | |
|---|---|---|
| PDF ( Single user document) |
$204.30 NZD
|
|
| HardCopy |
$227.00 NZD
|
|
| Networkable PDF |
Price varies
|
|
| Online Library ( Annual subscription) |
Info
Price varies
Online Library subscription information Online library subscriptions provide a cost-effective solution for organisations of any size to access the latest standards, offering 24/7 access to a personalised catalogue. The service ensures subscribers have have the most up-to-date version of selected standards, incluing automatic updates for any amendments or versions. Pricing is dependent on the chosen standards and the number of concurrent users, with discounts applied from the standards PDF price. For customised subscriptions or further inquiries, contact the Online Library team. |
AS/NZS 1554.1:2004 STRUCTURAL STEEL WELDING - WELDING OF STEEL STRUCTURES
PREFACE
CONTENTS
SECTION 1 SCOPE AND GENERAL
1.1 SCOPE
1.2 EXCLUSIONS
1.3 INNOVATION
1.4 REFERENCED DOCUMENTS
1.5 DEFINITIONS
1.5.1 Fabricator
1.5.2 Inspecting authority
1.5.3 Inspector
1.5.4 May
1.5.5 Principal
1.5.6 Shall
1.5.7 Should
1.6 WELD CATEGORIES
1.7 BASIC WELDING REQUIREMENTS
1.8 SAFETY
1.8.1 Safety equipment and procedures
1.8.2 Welding equipment
1.8.3 Other hazards
SECTION 2 MATERIALS OF CONSTRUCTION
2.1 PARENT MATERIAL
2.2 BACKING MATERIAL
2.3 WELDING CONSUMABLES
2.3.1 Electrodes and filler wires
2.3.2 Care of electrodes and filler wires
2.3.3 Flux
2.3.4 Shielding gas
SECTION 3 DETAILS OF WELDED CONNECTIONS
3.1 GENERAL
3.1.1 Permissible weld types
3.1.2 Design stresses
3.1.3 Drawings
3.2 BUTT WELDS
3.2.1 Size of weld
3.2.2 Design throat thickness
3.2.3 Effective length
3.2.4 Effective area
3.2.5 Transition of thickness or width
3.3 FILLET WELDS
3.3.1 Size of weld
3.3.2 Design throat thickness
3.3.3 Effective length
3.3.4 Effective area
3.3.5 Minimum size of fillet welds
3.3.6 Maximum size of fillet welds along edges
3.4 COMPOUND WELDS
3.4.1 Description
3.4.2 Design throat thickness (DTT)
3.5 SEAL WELDS
3.6 PLUG WELDS
3.7 SLOT WELDS
3.8 COMBINING STEEL SECTIONS
SECTION 4 QUALIFICATION OF PROCEDURES AND PERSONNEL
4.1 QUALIFICATION OF WELDING PROCEDURE
4.1.1 General
4.1.2 Butt welds
4.1.3 Fillet welds
4.1.4 Qualification of multiple welding positions
4.2 METHODS FOR QUALIFYING A WELDING PROCEDURE
4.3 PREQUALIFIED WELDING PROCEDURES
4.4 PORTABILITY OF QUALIFIED WELDING PROCEDURES
4.5 PREQUALIFIED JOINT PREPARATIONS
4.5.1 General
4.5.2 Prequalified complete penetration butt welds
4.5.3 Prequalified incomplete penetration butt welds
4.5.4 Prequalified fillet welds
4.5.5 Additional requirements for welds in hollow section members
4.6 QUALIFICATION OF WELDING CONSUMABLES
4.6.1 Prequalified welding consumables
4.6.2 Qualification of welding consumables by testing
4.7 QUALIFICATION OF WELDING PROCEDURE BY TESTING
4.7.1 Method of qualification
4.7.2 Preparation of special test piece
4.7.3 Dimensions of test pieces
4.7.4 Macro test
4.7.5 Transverse butt tensile test
4.7.6 Bend test
4.7.7 Charpy impact test
4.7.8 Hardness comparison test for parent metal and weld metal
4.7.9 Hardness test for weld-heat-affected zones
4.7.10 Retests
4.8 EXTENSION OF QUALIFICATION
4.9 COMBINATION OF PROCESSES
4.10 RECORDS OF TESTS
4.11 REQUALIFICATION OF WELDING PROCEDURES
4.12 QUALIFICATION OF WELDING PERSONNEL
4.12.1 Welding supervisor
4.12.2 Welders
SECTION 5 WORKMANSHIP
5.1 PREPARATION OF EDGES FOR WELDING
5.1.1 General
5.1.2 Thermal cutting
5.2 ASSEMBLY
5.2.1 General
5.2.2 Alignment of butt-welded joints
5.2.3 Alignment of fillet welds and incomplete penetration butt welds
5.2.4 Separation of a backing material
5.3 PREHEATING AND INTER-RUN CONTROL
5.3.1 General
5.3.2 Need for preheating
5.3.3 Extent of preheating and cooling after welding
5.3.4 Determination of preheating temperature
5.4 WELDING UNDER ADVERSE WEATHER CONDITIONS
5.5 TACK WELDS
5.6 WELD DEPTH-TO-WIDTH RATIO
5.7 CONTROL OF DISTORTION AND RESIDUAL STRESS
5.7.1 General
5.7.2 Stressed parts
5.7.3 Peening
5.7.4 Correction of distortion
5.8 BACKGOUGING AND REPAIR OF DEFECTS IN WELDS
5.8.1 General
5.8.2 Removal of weld metal
5.8.3 Grinding
5.8.4 Stop starts
5.9 TEMPORARY ATTACHMENTS
5.10 ARC STRIKES
5.11 CLEANING OF FINISHED WELDS
5.12 DRESSING OF BUTT WELDS
SECTION 6 QUALITY OF WELDS
6.1 CATEGORIES OF WELDS
6.2 METHODS OF INSPECTION AND PERMISSIBLE LEVELS OF IMPERFECTIONS
6.2.1 Methods of inspection of completed welds
6.2.2 Permissible levels of imperfection
6.2.3 Adjacent imperfections
6.2.4 Interpretation of tests
6.3 RADIOGRAPHY
6.3.1 Method
6.3.2 IQI sensitivity
6.3.3 Acceptance limits
6.4 ULTRASONIC EXAMINATION
6.4.1 Method
6.4.2 Evaluation
6.4.3 Acceptance limits
6.5 MAGNETIC PARTICLE EXAMINATION
6.6 LIQUID PENETRANT EXAMINATION
6.7 WELD DEFECTS
6.8 REPORTING
SECTION 7 INSPECTION
7.1 GENERAL
7.2 QUALIFICATIONS OF INSPECTORS
7.3 VISUAL INSPECTION OF WORK
7.4 NON-DESTRUCTIVE EXAMINATION OTHER THAN VISUAL
APPENDIX A - REFERENCED DOCUMENTS
APPENDIX B - BRITTLE FRACTURE
B1 METHODS
B2 NOTCH-DUCTILE RANGE METHOD
B3 DESIGN SERVICE TEMPERATURE
B3.1 General
B3.2 Basic design temperature
B3.3 Modifications to the basic design temperature
B4 MATERIAL SELECTION
B4.1 Selection of steel type
B4.2 Limitations
B4.3 Modification for certain applications
B5 FRACTURE ASSESSMENT
APPENDIX C - TYPICAL FORMS FOR WELDING PROCEDURES
APPENDIX D - MATTERS FOR RESOLUTION
APPENDIX E - WELDED JOINT AND PROCESS IDENTIFICATION
E1 NOTATION FOR JOINT IDENTIFICATION
E2 NOTATION FOR DIMENSIONS, POSITIONS AND BACKING MATERIAL
E3 NOTATION FOR PROCESSES
E4 EXAMPLE
Amendments
Previous versions
Keep me up-to-date
Sign up to receive updates when there are changes to this standard
Related Information
Code of Practice for Flammable Liquids Tank Wagons HSNOCOP 6-1 - Revoked
Ministry: Environmental Protection Authority
Section: 3.3.6.4
Citation context:Inspection of the welding shall be carried out in accordance with the welding specification (AS/NZS 1554 or AS/NZS 1665 as relevant) including:...
Code of Practice for Flammable Liquids Tank Wagons HSNOCOP 6-1 - Revoked
Ministry: Environmental Protection Authority
Section: 3.3.6.4
Citation context:Refers to 1554.1:2004(AS/NZS)A1. Inspection of the welding shall be carried out in accordance with the welding specification (AS/NZS 1554 or AS/NZS 1665 as relevant) including:...
Code of Practice for Flammable Liquids Tank Wagons HSNOCOP 6-1 - Revoked
Ministry: Environmental Protection Authority
Section: 1.6 References
Citation context:AS/NZS 1554 Structural Steel Welding parts 1, 4 and 5
A Code of Practice for the design and construction of vehicles for the bulk transportation of Class 6 toxic, Class 8 corrosive and Class 9 ecotoxic liquids by road HSNOCOP 39 - Revoked
Ministry: Environmental Protection Authority
Section: 2.8.2
Citation context:Refers to 1554.1:2004(AS/NZS)A1. Welding of steel components for structural purposes necessary in building any new tank wagon or in modifying any existing tank wagon shall conform to the provisions of AS/NZS 1554.
A Code of Practice for the design and construction of vehicles for the bulk transportation of Class 6 toxic, Class 8 corrosive and Class 9 ecotoxic liquids by road HSNOCOP 39 - Revoked
Ministry: Environmental Protection Authority
Section: 5.4.5
Citation context:Inspection of the welding shall be carried out in accordance with the welding specification (AS/NZS 1554 or AS/NZS 1665 as relevant) including:...
A Code of Practice for the design and construction of vehicles for the bulk transportation of Class 6 toxic, Class 8 corrosive and Class 9 ecotoxic liquids by road HSNOCOP 39 - Revoked
Ministry: Environmental Protection Authority
Section: 1.7 References
Citation context:Refers to 1554.1:2004(AS/NZS)A1. AS/NZS 1554 Structural Steel Welding parts 1, 4, 5 and 6
A Code of Practice for the design and construction of vehicles for the bulk transportation of Class 6 toxic, Class 8 corrosive and Class 9 ecotoxic liquids by road HSNOCOP 39 - Revoked
Ministry: Environmental Protection Authority
Section: 5.4.5
Citation context:Refers to 1554.1:2004(AS/NZS)A1. Inspection of the welding shall be carried out in accordance with the welding specification (AS/NZS 1554 or AS/NZS 1665 as relevant) including:...
Best Practice Guideline For Scaffolding In New Zealand
Ministry: Scaffolding and Rigging New Zealand
Section: 1.2.1.1
Citation context:Relevant standards are those related to… …This includes but is not limited to the following: ...AS/NZS 1554.1 Structural steel welding - Welding of steel structures...
Code of Practice for Flammable Liquids Tank Wagons HSNOCOP 6-1 - Revoked
Ministry: Environmental Protection Authority
Section: 3.3.6.2
Citation context:Welding of steel shall be in accordance with AS/NZS 1554 Structural Steel Welding parts 1, 4 and 5 (or equivalent) as appropriate. This includes all requirements for qualification of welding personnel.
Approved Code Of Practice For Cranes
Ministry: WorkSafe New Zealand
Section: 13.2(2)
Citation context:Welding is to be carried out in accordance with the requirements of the construction standard or AS/NZS: 1554 Structural steel welding...
Approved Code Of Practice For Cranes
Ministry: WorkSafe New Zealand
Section: Appendix C Referenced documents
Citation context:AS/NZS 1554 (set) Structural Steel Welding
Code Of Practice For Flammable Gases And Oxygen Tank Wagons 2008-Revoked
Ministry: Environmental Protection Authority
Section: 2.10.2
Citation context:Welding of steel shall be in accordance with AS/NZS 1554 Structural Steel Welding parts 1, 4 and 5 (or equivalent) as appropriate. This includes all requirements for qualification of welding personnel.
Code of Practice for Flammable Liquids Tank Wagons HSNOCOP 6-1 - Revoked
Ministry: Environmental Protection Authority
Section: 1.6 References
Citation context:Refers to 1554.1:2004(AS/NZS)A1. AS/NZS 1554 Structural Steel Welding parts 1, 4 and 5
Code of Practice for Flammable Liquids Tank Wagons HSNOCOP 6-1 - Revoked
Ministry: Environmental Protection Authority
Section: 3.3.6.2
Citation context:Refers to 1554.1:2004(AS/NZS)A1. Welding of steel shall be in accordance with AS/NZS 1554 Structural Steel Welding parts 1, 4 and 5 (or equivalent) as appropriate. This includes all requirements for qualification of welding personnel.
A Code of Practice for the design and construction of vehicles for the bulk transportation of Class 6 toxic, Class 8 corrosive and Class 9 ecotoxic liquids by road HSNOCOP 39 - Revoked
Ministry: Environmental Protection Authority
Section: 1.7 References
Citation context:AS/NZS 1554 Structural Steel Welding parts 1, 4, 5 and 6
A Code of Practice for the design and construction of vehicles for the bulk transportation of Class 6 toxic, Class 8 corrosive and Class 9 ecotoxic liquids by road HSNOCOP 39 - Revoked
Ministry: Environmental Protection Authority
Section: 2.8.2
Citation context:Welding of steel components for structural purposes necessary in building any new tank wagon or in modifying any existing tank wagon shall conform to the provisions of AS/NZS 1554.
Similar Standards
-
AS/NZS 1554.1:2014
Structural steel welding - Part 1: Welding of steel structures -
AS/NZS 1554.1:2014 A1
Structural steel welding - Part 1: Welding of steel structures: Amendment 1 -
AS/NZS 1554.1:2014 A2
Structural steel welding - Part 1: Welding of steel structures: Amendment 2 -
AS/NZS 1554.2:2003
Structural steel welding - Stud welding (steel studs to steel)
AS/NZS 1554.1:2004 STRUCTURAL STEEL WELDING - WELDING OF STEEL STRUCTURES
PREFACE
CONTENTS
SECTION 1 SCOPE AND GENERAL
1.1 SCOPE
1.2 EXCLUSIONS
1.3 INNOVATION
1.4 REFERENCED DOCUMENTS
1.5 DEFINITIONS
1.5.1 Fabricator
1.5.2 Inspecting authority
1.5.3 Inspector
1.5.4 May
1.5.5 Principal
1.5.6 Shall
1.5.7 Should
1.6 WELD CATEGORIES
1.7 BASIC WELDING REQUIREMENTS
1.8 SAFETY
1.8.1 Safety equipment and procedures
1.8.2 Welding equipment
1.8.3 Other hazards
SECTION 2 MATERIALS OF CONSTRUCTION
2.1 PARENT MATERIAL
2.2 BACKING MATERIAL
2.3 WELDING CONSUMABLES
2.3.1 Electrodes and filler wires
2.3.2 Care of electrodes and filler wires
2.3.3 Flux
2.3.4 Shielding gas
SECTION 3 DETAILS OF WELDED CONNECTIONS
3.1 GENERAL
3.1.1 Permissible weld types
3.1.2 Design stresses
3.1.3 Drawings
3.2 BUTT WELDS
3.2.1 Size of weld
3.2.2 Design throat thickness
3.2.3 Effective length
3.2.4 Effective area
3.2.5 Transition of thickness or width
3.3 FILLET WELDS
3.3.1 Size of weld
3.3.2 Design throat thickness
3.3.3 Effective length
3.3.4 Effective area
3.3.5 Minimum size of fillet welds
3.3.6 Maximum size of fillet welds along edges
3.4 COMPOUND WELDS
3.4.1 Description
3.4.2 Design throat thickness (DTT)
3.5 SEAL WELDS
3.6 PLUG WELDS
3.7 SLOT WELDS
3.8 COMBINING STEEL SECTIONS
SECTION 4 QUALIFICATION OF PROCEDURES AND PERSONNEL
4.1 QUALIFICATION OF WELDING PROCEDURE
4.1.1 General
4.1.2 Butt welds
4.1.3 Fillet welds
4.1.4 Qualification of multiple welding positions
4.2 METHODS FOR QUALIFYING A WELDING PROCEDURE
4.3 PREQUALIFIED WELDING PROCEDURES
4.4 PORTABILITY OF QUALIFIED WELDING PROCEDURES
4.5 PREQUALIFIED JOINT PREPARATIONS
4.5.1 General
4.5.2 Prequalified complete penetration butt welds
4.5.3 Prequalified incomplete penetration butt welds
4.5.4 Prequalified fillet welds
4.5.5 Additional requirements for welds in hollow section members
4.6 QUALIFICATION OF WELDING CONSUMABLES
4.6.1 Prequalified welding consumables
4.6.2 Qualification of welding consumables by testing
4.7 QUALIFICATION OF WELDING PROCEDURE BY TESTING
4.7.1 Method of qualification
4.7.2 Preparation of special test piece
4.7.3 Dimensions of test pieces
4.7.4 Macro test
4.7.5 Transverse butt tensile test
4.7.6 Bend test
4.7.7 Charpy impact test
4.7.8 Hardness comparison test for parent metal and weld metal
4.7.9 Hardness test for weld-heat-affected zones
4.7.10 Retests
4.8 EXTENSION OF QUALIFICATION
4.9 COMBINATION OF PROCESSES
4.10 RECORDS OF TESTS
4.11 REQUALIFICATION OF WELDING PROCEDURES
4.12 QUALIFICATION OF WELDING PERSONNEL
4.12.1 Welding supervisor
4.12.2 Welders
SECTION 5 WORKMANSHIP
5.1 PREPARATION OF EDGES FOR WELDING
5.1.1 General
5.1.2 Thermal cutting
5.2 ASSEMBLY
5.2.1 General
5.2.2 Alignment of butt-welded joints
5.2.3 Alignment of fillet welds and incomplete penetration butt welds
5.2.4 Separation of a backing material
5.3 PREHEATING AND INTER-RUN CONTROL
5.3.1 General
5.3.2 Need for preheating
5.3.3 Extent of preheating and cooling after welding
5.3.4 Determination of preheating temperature
5.4 WELDING UNDER ADVERSE WEATHER CONDITIONS
5.5 TACK WELDS
5.6 WELD DEPTH-TO-WIDTH RATIO
5.7 CONTROL OF DISTORTION AND RESIDUAL STRESS
5.7.1 General
5.7.2 Stressed parts
5.7.3 Peening
5.7.4 Correction of distortion
5.8 BACKGOUGING AND REPAIR OF DEFECTS IN WELDS
5.8.1 General
5.8.2 Removal of weld metal
5.8.3 Grinding
5.8.4 Stop starts
5.9 TEMPORARY ATTACHMENTS
5.10 ARC STRIKES
5.11 CLEANING OF FINISHED WELDS
5.12 DRESSING OF BUTT WELDS
SECTION 6 QUALITY OF WELDS
6.1 CATEGORIES OF WELDS
6.2 METHODS OF INSPECTION AND PERMISSIBLE LEVELS OF IMPERFECTIONS
6.2.1 Methods of inspection of completed welds
6.2.2 Permissible levels of imperfection
6.2.3 Adjacent imperfections
6.2.4 Interpretation of tests
6.3 RADIOGRAPHY
6.3.1 Method
6.3.2 IQI sensitivity
6.3.3 Acceptance limits
6.4 ULTRASONIC EXAMINATION
6.4.1 Method
6.4.2 Evaluation
6.4.3 Acceptance limits
6.5 MAGNETIC PARTICLE EXAMINATION
6.6 LIQUID PENETRANT EXAMINATION
6.7 WELD DEFECTS
6.8 REPORTING
SECTION 7 INSPECTION
7.1 GENERAL
7.2 QUALIFICATIONS OF INSPECTORS
7.3 VISUAL INSPECTION OF WORK
7.4 NON-DESTRUCTIVE EXAMINATION OTHER THAN VISUAL
APPENDIX A - REFERENCED DOCUMENTS
APPENDIX B - BRITTLE FRACTURE
B1 METHODS
B2 NOTCH-DUCTILE RANGE METHOD
B3 DESIGN SERVICE TEMPERATURE
B3.1 General
B3.2 Basic design temperature
B3.3 Modifications to the basic design temperature
B4 MATERIAL SELECTION
B4.1 Selection of steel type
B4.2 Limitations
B4.3 Modification for certain applications
B5 FRACTURE ASSESSMENT
APPENDIX C - TYPICAL FORMS FOR WELDING PROCEDURES
APPENDIX D - MATTERS FOR RESOLUTION
APPENDIX E - WELDED JOINT AND PROCESS IDENTIFICATION
E1 NOTATION FOR JOINT IDENTIFICATION
E2 NOTATION FOR DIMENSIONS, POSITIONS AND BACKING MATERIAL
E3 NOTATION FOR PROCESSES
E4 EXAMPLE
Amendments
Previous versions
AS/NZS 1554.1:2004
Online Library subscription information
Online library subscriptions provide a cost-effective solution for organisations of any size to access the latest standards, offering 24/7 access to a personalised catalogue. The service ensures subscribers have have the most up-to-date version of selected standards, incluing automatic updates for any amendments or versions. Pricing is dependent on the chosen standards and the number of concurrent users, with discounts applied from the standards PDF price. For customised subscriptions or further inquiries, contact the Online Library team.