AS/NZS 5601.2:2013
Gas installations - Part 2: LP Gas installations in caravans and boats for non-propulsive purposes
Provides essential requirements and deemed-to-comply solutions, to promote uniform standards of gas installation and to provide a stand-alone standard for LP Gas installations in caravans and boats for non-propulsive purposes. Legislative changes in 1992 removed the responsibility for inspection and certification of gas installations from the gas suppliers and instituted a regime of gas certification by a person authorised under the Plumbers, Gasfitters and Drainlayers Act 2006. Section 1 of this standard details the scope and general aspects of a gas installation that contribute to its safety. Section 2 outlines performance-based design and other essential requirements that must be met to ensure the safety of gas installations. Sections 3 to 9 specify the means of compliance for installations within the limitations of section 2. Gas installations must be undertaken only by persons authorised under the Plumbers, Gasfitters and Drainlayers Act 2006.
| Get this standard | Prices exclude GST | |
|---|---|---|
| PDF ( Single user document) |
$217.80 NZD
|
|
| HardCopy |
$242.00 NZD
|
|
| Networkable PDF |
Price varies
|
|
| Online Library ( Annual subscription) |
Info
Price varies
Online Library subscription information Online library subscriptions provide a cost-effective solution for organisations of any size to access the latest standards, offering 24/7 access to a personalised catalogue. The service ensures subscribers have have the most up-to-date version of selected standards, incluing automatic updates for any amendments or versions. Pricing is dependent on the chosen standards and the number of concurrent users, with discounts applied from the standards PDF price. For customised subscriptions or further inquiries, contact the Online Library team. |
AS/NZS 5601.2:2013 GAS INSTALLATIONS - LP GAS INSTALLATIONS IN CARAVANS AND BOATS FOR NON-PROPULSIVE PURPOSES
PREFACE
CONTENTS
SECTION 1 SCOPE AND GENERAL
1.1 SCOPE
1.2 APPLICATION
1.3 EXCLUSIONS
1.4 NORMATIVE REFERENCES
1.5 COMPLIANCE
1.6 OCCUPATIONAL HEALTH AND SAFETY
1.7 DEFINITIONS
1.7.1 Accessible
1.7.2 Appliance
1.7.3 Authorized person
1.7.4 Bedroom or sleeping area
1.7.5 Boat
1.7.6 Burner
1.7.7 Caravan
1.7.8 Carbon monoxide detector
1.7.9 Certified/certification
1.7.10 Certifying body
1.7.11 Combustible material
1.7.12 Combustible surface
1.7.13 Combustion products
1.7.14 Competent person
1.7.15 Cylinder
1.7.16 Cylinder compartment
1.7.17 Deck (see Figure 1.1)
1.7.18 DN (diametre nominale)
1.7.19 Exhaust fan
1.7.20 Explosive limit
1.7.21 Fire resistant material
1.7.22 Flame safeguard system
1.7.23 Flue
1.7.24 Flue cowl
1.7.25 Flue gases
1.7.26 Flue terminal
1.7.27 Gas consumption
1.7.28 Gas detector
1.7.29 Gas installation
1.7.30 Gas/Liquefied petroleum gas (LP Gas)
1.7.31 Gas load
1.7.32 Gas pressure regulator
1.7.33 Gastight
1.7.34 Hob
1.7.35 Hose assembly
1.7.36 Ignition source
1.7.37 LP Gas locker
1.7.38 Main run
1.7.39 Manual shut-off valve
1.7.40 Manufacturer's specifications/instructions/recommendations
1.7.41 May
1.7.42 Nominal size/Nominal diameter (DN)
1.7.43 Operating pressure
1.7.44 Outdoor(s)
1.7.45 Oxygen-depletion sensor (ODS) or device
1.7.46 Pigtail
1.7.47 Piping
1.7.48 POL fitting (Prest-o-lite fitting)
1.7.49 Pressure
1.7.50 Proprietary system
1.7.51 Quick-connect device
1.7.52 Range hood
1.7.53 Rated working pressure
1.7.54 Room-sealed appliance
1.7.55 Safety shut-off valve
1.7.56 Shall
1.7.57 Should
1.7.58 Technical Regulator
1.7.59 Trivet
1.7.60 Vent line
1.7.61 Water heater
SECTION 2 PERFORMANCE BASED DESIGN, INSTALLATION AND OTHER ESSENTIAL REQUIREMENTS
2.1 GENERAL
2.2 GENERAL WORK
2.2.1 Verification of gas supply
2.2.2 Work on a gas installation
2.2.3 Sealing of open ends
2.2.4 Testing of gas installations
2.2.5 Acceptable substances for testing
2.2.6 Methods of locating gas leaks
2.2.7 Decommissioning
2.3 LP GAS CYLINDERS
2.3.1 Cylinders
2.3.2 Corrosion
2.3.3 Cylinder orientation
2.3.4 Use of in-situ fill cylinders in boats
2.3.5 Multi-cylinder installations
2.4 LOCATION OF LP GAS CYLINDERS
2.4.1 Restriction on location of cylinders
2.4.2 Required clearances around a cylinder
2.4.3 Mounting and stowage
2.4.4 Cylinder restraint
2.5 CYLINDER COMPARTMENTS AND LP GAS LOCKERS
2.5.1 Design and construction
2.5.2 Identification of cylinder compartment or LP Gas locker
2.6 MATERIALS AND FITTINGS
2.6.1 Material and components to be suitable
2.6.2 Proprietary systems
2.6.3 Jointing
2.6.4 Condition of pipe and fittings
2.6.5 Prohibition of earthing through piping
2.6.6 Condition of pipe during installation
2.6.7 Restriction on use of thread sealant
2.6.8 Bending pipe
2.7 PIPING
2.7.1 General
2.7.2 Design
2.7.3 Pipe size
2.7.4 Pipe size for piping supplying a Type A appliance
2.7.5 Location
2.7.6 Support of piping
2.7.7 Corrosion control
2.7.8 Gas pressure regulator
2.7.9 Over-pressure protection
2.7.10 Pressure test points
2.7.11 Gas venting
2.8 FLUES
2.8.1 General
2.8.2 Design
2.8.3 Materials
2.8.4 Installation
2.8.5 Location
2.8.6 Flue terminals
2.9 INSTALLING GAS APPLIANCES
2.9.1 Prohibition on installation
2.9.2 Pre-installation
2.9.3 General installation requirements
2.9.4 Requirements for gas appliances
2.9.5 Gas appliance location
2.9.6 Ventilation of the gas appliance space and air supply to gas appliances
2.9.7 Gas appliance connection and isolation
2.9.8 Commissioning
2.10 MATERIALS AND COMPONENTS-GENERAL
2.10.1 Prohibited fittings
2.10.2 Fire resistant material
2.10.3 Flue materials
2.10.4 Jointing compounds and materials
2.11 HOSE ASSEMBLIES
2.11.1 General
2.11.2 Use of a hose assembly
2.11.3 Hose assembly-Operating conditions
2.11.4 Hose assembly connecting an appliance
2.12 SHUT-OFF VALVES
2.13 QUICK-CONNECT DEVICES
2.13.1 General
2.13.2 Restriction on installation
2.14 'Text deleted'
SECTION 3 MEANS OF COMPLIANCE-CYLINDERS
3.1 GENERAL
3.1.1 Cylinders
3.1.2 Corrosion
3.1.3 Cylinder orientation
3.1.4 Use of in-situ fill cylinders in boats
3.1.5 Multi-cylinder installations
3.2 LOCATION OF LP GAS CYLINDERS
3.2.1 Restriction on location of cylinders
3.2.2 Required clearances around a cylinder
3.2.3 Mounting and stowage
3.2.4 Stowage of spare cylinders
3.2.5 Heat shield
3.3 CYLINDER ATTACHMENT
3.3.1 Restraints
3.3.2 Structures
3.4 CYLINDER COMPARTMENTS AND LP GAS LOCKERS
3.4.1 Caravans
3.4.2 Cylinders located in a combined storage compartment/locker for caravans
3.4.3 Boats
3.4.4 'Text deleted'
3.4.5 Access to cylinder compartments
3.4.6 Identification of cylinder compartment or LP Gas locker
SECTION 4 MEANS OF COMPLIANCE-GAS PRESSURE REGULATORS
4.1 SUITABILITY OF PRESSURE REGULATORS
4.2 OUTLET PRESSURE
4.3 MOUNTING AND SUPPORT OF REGULATOR
SECTION 5 MEANS OF COMPLIANCE-PIPING AND FITTINGS
5.1 GENERAL
5.1.1 Location
5.1.2 Size
5.1.3 Construction
5.1.4 Piping specification
5.1.5 Cylinder connections
5.2 INSTALLATION OF PIPING
5.2.1 General requirements
5.2.2 Piping in caravans
5.2.3 Piping in boats
5.2.4 Rigid piping
5.2.5 Hose assemblies
5.2.6 Prohibition on earthing of piping
5.2.7 Isolation valves
5.2.8 Quick-connect devices
5.2.9 Jointing compounds and materials
5.2.10 Pipe supports and fixings
5.2.11 Sealing of open ends
SECTION 6 MEANS OF COMPLIANCE-GAS APPLIANCES
6.1 PROHIBITED APPLIANCES
6.2 RESTRICTION FOR STOWED APPLIANCES
6.3 FLAME SAFEGUARD SYSTEM
6.4 MANUFACTURER'S INSTRUCTIONS
6.5 CLEARANCES
6.6 DISTANCE FROM SOURCES OF FUEL
6.7 RESTRICTION ON INSTALLATION OF AN APPLIANCE ON A PETROL-FUELLED BOAT
6.8 ELECTRICAL REQUIREMENTS
6.8.1 General
6.8.2 For Australian use only
6.9 SPACE HEATERS
6.10 COOKING APPLIANCES
6.10.1 Clearances around gas cooking appliances
6.10.2 Protection of a combustible surface near a gas cooking appliance
6.10.3 Vapour seal
6.10.4 Warning labels for cooking appliances
6.10.5 Cooking appliances on boats
6.11 REFRIGERATORS
6.11.1 Flues
6.11.2 Vents
6.11.3 Clearances
6.11.4 Ventilation
6.12 INSTANTANEOUS WATER HEATERS
6.13 SPA POOL HEATERS ON BOATS
6.13.1 Prohibited locations
6.13.2 Supporting base
6.13.3 Control systems
6.13.4 Requirement for pool heater where flow and return water pipes are of plastic
6.13.5 Non-return valve required
6.13.6 Restriction on fitting of a valve in water flow line
6.14 GAS BARBECUES AND RADIANT GAS HEATERS FOR OUTDOOR USE
SECTION 7 MEANS OF COMPLIANCE-VENTILATION
7.1 GENERAL
7.2 APPROPRIATE VENTILATION SYSTEMS
7.3 VENTILATION OPENINGS-CARAVANS AND BOATS
7.3.1 Minimum free area
7.3.2 Special requirements for camper trailers and boats
7.3.3 Special requirements for RVs (motorized caravans)
7.4 POSITION OF OPENINGS-CARAVANS ONLY
7.4.1 Cross ventilation
7.4.2 Distance from ceiling
7.4.3 Distance from floor
7.4.4 Vent warning label
7.5 POSITION OF OPENINGS-BOATS ONLY
7.6 GAS DETECTION SYSTEM REQUIRED-BOATS ONLY
SECTION 8 MEANS OF COMPLIANCE-FLUEING
8.1 FLUE CONSTRUCTION AND CLEARANCES
8.2 PROTECTION FROM ENVIRONMENTAL EFFECTS
8.3 DISTURBANCES
8.4 LOCATION OF FLUE TERMINAL
8.4.1 General
8.4.2 Termination of a flue under a cover
8.5 FLUE MATERIALS
8.6 PROPRIETARY FLUEING SYSTEMS
SECTION 9 MEANS OF COMPLIANCE-TESTING AND COMMISSIONING
9.1 TESTING FOR GASTIGHTNESS
9.2 COMMISSIONING
9.2.1 Commissioning of appliance
9.2.2 Other commissioning checks
SECTION 10 COMPLIANCE, MARKINGS AND LABELS
10.1 GAS COMPLIANCE PLATE
10.2 LABELS AND MARKINGS ADJACENT TO GAS CYLINDERS
10.3 LABELS AND MARKINGS NEAR GAS APPLIANCES
10.3.1 General
10.3.2 Additional marking for boats
APPENDIX A - NORMATIVE REFERENCES
APPENDIX B - CONVERSION FACTORS
APPENDIX C - FIRE RESISTANT MATERIAL
C1 GENERAL
C2 SPECIFICATION FOR FIRE RESISTANT MATERIAL
C3 EXAMPLES TO DETERMINE REQUIRED THICKNESS OF FIRE RESISTANT MATERIAL
C4 ACCEPTABLE METHODS OF PROTECTION
APPENDIX D - PIPE SIZING
D1 INTRODUCTION
D1.1 General
D1.2 Pipe conditions
D1.3 Fitting allowance
D1.4 Equations used
D1.5 Excessive gas velocities
D2 NEW PIPING SYSTEMS
D3 EXISTING PIPING SYSTEMS
D4 INFORMATION REQUIRED
D5 DESIGN PROCEDURE USING PIPE SIZING GRAPHS
D5.1 Introduction
D5.2 Sketch the piping layout
D5.3 Tabulate the pipe runs
D5.4 Determine the length of the longest pipe run
D5.5 Determine the allowable pressure drop per metre
D5.6 Determine the required pipe size from the pipe sizing graphs
D5.7 Pipe sizing graphs
D6 DESIGN PROCEDURE USING PIPE SIZING TABLES
D6.1 General
D6.2 Sketch the piping layout
D6.3 Determine the main run
D6.4 Select the piping material
D6.5 Tabulate the pipe runs
D6.6 Selecting the pipe size
D6.7 Pipe sizing tables
APPENDIX E - COMBUSTIBLE GAS DETECTION SYSTEMS FOR BOATS
E1 GENERAL
E2 GAS DETECTION SYSTEM
E3 INSTALLATION OF THE SYSTEM
E3.1 Solenoid valve
E3.2 Position of audible alarm
E3.3 Sensors
E3.4 Operation of the system when gas is detected
APPENDIX F - TESTING GAS INSTALLATIONS
F1 GENERAL
F1.1 New installations
F1.2 Additions and alterations to installations
F2 PIPEWORK TEST
F2.1 Method
F2.2 Test result
F3 INSTALLATION GAS TIGHTNESS TEST
F3.1 General
F3.2 Method 1-Pressure loss
F3.3 Method 2-Using bubble leakage detector
F4 METHODS OF LOCATING GAS LEAKS
APPENDIX G - CONSUMER INSTRUCTIONS
APPENDIX H - METHOD OF LOCATING GAS PRESSURE REGULATORS
APPENDIX I - GUIDELINES FOR GAS APPLIANCE COMMISSIONING
I1 GENERAL
I2 STOVES, COOKERS AND HOT PLATES
I3 INSTANTANEOUS WATER HEATERS
I4 STORAGE WATER HEATERS
APPENDIX J - SYMBOLS USED IN GAS CONTROL SYSTEM DIAGRAMS
APPENDIX K - GAS INSTALLATION CHECKLIST
APPENDIX L - APPLIANCES IN OUTDOOR AREAS
L1 DIAGRAMMATIC REPRESENTATION OF OUTDOOR AREAS
L2 DOMESTIC GAS BARBECUES AND RADIANT GAS HEATERS
BIBLIOGRAPHY
Keep me up-to-date
Sign up to receive updates when there are changes to this standard
Related Information
Gas (Safety And Measurement) Regulations 2010
Ministry: WorkSafe New Zealand: Energy Safety
Section: 44(1)
Citation context:(1) Every person who designs, installs, tests, commissions, or connects a gas installation or part installation must design, install, test, commission, and connect the gas installation or part installation in accordance with any applicable certified design and whichever of the following applies:... ...(b) AS/NZS 5601.2.
Gas (Safety And Measurement) Regulations 2010
Ministry: WorkSafe New Zealand: Energy Safety
Section: 44(5)
Citation context:(5) For the purposes of subclauses (1) to (3)... ...(b) despite anything to the contrary in AS/NZS 5601.2, a gas installation does not fail to be a gas installation to which AS/NZS 5601.2 applies by reason only that it receives gas at a supply pressure of more than 3 kilopascals.
Gas (Safety And Measurement) Regulations 2010
Ministry: WorkSafe New Zealand: Energy Safety
Section: 45(1)
Citation context:(1) All gasfitting work done on a gas installation or part installation must be tested... ...(d) in the case of a gas installation or part installation that does not comply with sections 3 to 6 of AS/NZS 5601.1 or sections 3 to 9 of AS/NZS 5601.2 (as applicable), in accordance with the verification or testing process set out in the certified design for the gas installation or part installation.
Gas (Safety And Measurement) Regulations 2010
Ministry: WorkSafe New Zealand: Energy Safety
Section: Schedule 1
Citation context:AS/NZS 5601.2–2013: New Zealand Standard known as AS/NZS5601.2:2013 (Gas installations—Part 2: LP Gas installations in caravans and boats for non-propulsive purposes)
Gas (Safety And Measurement) Regulations 2010
Ministry: WorkSafe New Zealand: Energy Safety
Section: 51(1)
Citation context:(1) Before a person connects a gas installation or part installation on which gasfitting work has been done to a gas supply, the person doing the connection or, if subclause (5) applies, the supervisor must... ...(g) if the gas installation or part installation is an imported gas installation or part installation, ensure that it complies with the requirements of section 2 of AS/NZS 5601.1 or section 2 of AS/NZS 5601.2 (as applicable).
Gas (Safety And Measurement) Regulations 2010
Ministry: WorkSafe New Zealand: Energy Safety
Section: 44(2)
Citation context:(2) If a gas installation or part installation does not comply with either sections 3 to 6 of AS/NZS 5601.1 or sections 3 to 9 of AS/NZS 5601.2, any person who installs, tests, commissions, or connects the installation or part installation must do so in accordance with a certified design.
Gas (Safety And Measurement) Regulations 2010
Ministry: WorkSafe New Zealand: Energy Safety
Section: 5A(2)
Citation context:In these regulations, high-risk gasfitting means any of the following, unless it is low-risk gasfitting:... ...(b) any gasfitting, other than that described in paragraph (a), that... ...(vi) is carried out in accordance with AS/NZS 5601.2 where the operating pressure is greater than 3 kilopascals.
Gas (Safety And Measurement) Regulations 2010
Ministry: WorkSafe New Zealand: Energy Safety
Section: 44(3)
Citation context:(3) Every person who supplies or intends to supply an imported gas installation to a retailer or consumer must, before supplying the gas installation, ensure that it complies with the requirements of section 2 of whichever of the following applies:... ...(b) AS/NZS 5601.2.
Gas (Safety And Measurement) Regulations 2010
Ministry: WorkSafe New Zealand: Energy Safety
Section: 48(1)
Citation context:(1) Every certificate of compliance must record the following:... ...(a) whether the work has been done in accordance with sections 3 to 6 of AS/NZS 5601.1 or in accordance with sections 3 to 9 of AS/NZS 5601.2.... ...(c) if the work was required to comply with standards in addition to AS/NZS 5601.1 or AS/NZS 5601.2 (as applicable), which standards were complied with.
Similar Standards
-
AS/NZS 4552.2:2010
Gas fired water heaters for hot water supply and/or central heating - Minimum energy performance standards for gas water heaters
-
AS/NZS 4645.1:2018
Gas distribution networks - Part 1: Network management -
AS/NZS 4645.2:2018
Gas distribution networks - Part 2: Steel pipe systems -
AS/NZS 4645.3:2018
Gas distribution networks - Part 3: Plastics pipe systems
AS/NZS 5601.2:2013 GAS INSTALLATIONS - LP GAS INSTALLATIONS IN CARAVANS AND BOATS FOR NON-PROPULSIVE PURPOSES
PREFACE
CONTENTS
SECTION 1 SCOPE AND GENERAL
1.1 SCOPE
1.2 APPLICATION
1.3 EXCLUSIONS
1.4 NORMATIVE REFERENCES
1.5 COMPLIANCE
1.6 OCCUPATIONAL HEALTH AND SAFETY
1.7 DEFINITIONS
1.7.1 Accessible
1.7.2 Appliance
1.7.3 Authorized person
1.7.4 Bedroom or sleeping area
1.7.5 Boat
1.7.6 Burner
1.7.7 Caravan
1.7.8 Carbon monoxide detector
1.7.9 Certified/certification
1.7.10 Certifying body
1.7.11 Combustible material
1.7.12 Combustible surface
1.7.13 Combustion products
1.7.14 Competent person
1.7.15 Cylinder
1.7.16 Cylinder compartment
1.7.17 Deck (see Figure 1.1)
1.7.18 DN (diametre nominale)
1.7.19 Exhaust fan
1.7.20 Explosive limit
1.7.21 Fire resistant material
1.7.22 Flame safeguard system
1.7.23 Flue
1.7.24 Flue cowl
1.7.25 Flue gases
1.7.26 Flue terminal
1.7.27 Gas consumption
1.7.28 Gas detector
1.7.29 Gas installation
1.7.30 Gas/Liquefied petroleum gas (LP Gas)
1.7.31 Gas load
1.7.32 Gas pressure regulator
1.7.33 Gastight
1.7.34 Hob
1.7.35 Hose assembly
1.7.36 Ignition source
1.7.37 LP Gas locker
1.7.38 Main run
1.7.39 Manual shut-off valve
1.7.40 Manufacturer's specifications/instructions/recommendations
1.7.41 May
1.7.42 Nominal size/Nominal diameter (DN)
1.7.43 Operating pressure
1.7.44 Outdoor(s)
1.7.45 Oxygen-depletion sensor (ODS) or device
1.7.46 Pigtail
1.7.47 Piping
1.7.48 POL fitting (Prest-o-lite fitting)
1.7.49 Pressure
1.7.50 Proprietary system
1.7.51 Quick-connect device
1.7.52 Range hood
1.7.53 Rated working pressure
1.7.54 Room-sealed appliance
1.7.55 Safety shut-off valve
1.7.56 Shall
1.7.57 Should
1.7.58 Technical Regulator
1.7.59 Trivet
1.7.60 Vent line
1.7.61 Water heater
SECTION 2 PERFORMANCE BASED DESIGN, INSTALLATION AND OTHER ESSENTIAL REQUIREMENTS
2.1 GENERAL
2.2 GENERAL WORK
2.2.1 Verification of gas supply
2.2.2 Work on a gas installation
2.2.3 Sealing of open ends
2.2.4 Testing of gas installations
2.2.5 Acceptable substances for testing
2.2.6 Methods of locating gas leaks
2.2.7 Decommissioning
2.3 LP GAS CYLINDERS
2.3.1 Cylinders
2.3.2 Corrosion
2.3.3 Cylinder orientation
2.3.4 Use of in-situ fill cylinders in boats
2.3.5 Multi-cylinder installations
2.4 LOCATION OF LP GAS CYLINDERS
2.4.1 Restriction on location of cylinders
2.4.2 Required clearances around a cylinder
2.4.3 Mounting and stowage
2.4.4 Cylinder restraint
2.5 CYLINDER COMPARTMENTS AND LP GAS LOCKERS
2.5.1 Design and construction
2.5.2 Identification of cylinder compartment or LP Gas locker
2.6 MATERIALS AND FITTINGS
2.6.1 Material and components to be suitable
2.6.2 Proprietary systems
2.6.3 Jointing
2.6.4 Condition of pipe and fittings
2.6.5 Prohibition of earthing through piping
2.6.6 Condition of pipe during installation
2.6.7 Restriction on use of thread sealant
2.6.8 Bending pipe
2.7 PIPING
2.7.1 General
2.7.2 Design
2.7.3 Pipe size
2.7.4 Pipe size for piping supplying a Type A appliance
2.7.5 Location
2.7.6 Support of piping
2.7.7 Corrosion control
2.7.8 Gas pressure regulator
2.7.9 Over-pressure protection
2.7.10 Pressure test points
2.7.11 Gas venting
2.8 FLUES
2.8.1 General
2.8.2 Design
2.8.3 Materials
2.8.4 Installation
2.8.5 Location
2.8.6 Flue terminals
2.9 INSTALLING GAS APPLIANCES
2.9.1 Prohibition on installation
2.9.2 Pre-installation
2.9.3 General installation requirements
2.9.4 Requirements for gas appliances
2.9.5 Gas appliance location
2.9.6 Ventilation of the gas appliance space and air supply to gas appliances
2.9.7 Gas appliance connection and isolation
2.9.8 Commissioning
2.10 MATERIALS AND COMPONENTS-GENERAL
2.10.1 Prohibited fittings
2.10.2 Fire resistant material
2.10.3 Flue materials
2.10.4 Jointing compounds and materials
2.11 HOSE ASSEMBLIES
2.11.1 General
2.11.2 Use of a hose assembly
2.11.3 Hose assembly-Operating conditions
2.11.4 Hose assembly connecting an appliance
2.12 SHUT-OFF VALVES
2.13 QUICK-CONNECT DEVICES
2.13.1 General
2.13.2 Restriction on installation
2.14 'Text deleted'
SECTION 3 MEANS OF COMPLIANCE-CYLINDERS
3.1 GENERAL
3.1.1 Cylinders
3.1.2 Corrosion
3.1.3 Cylinder orientation
3.1.4 Use of in-situ fill cylinders in boats
3.1.5 Multi-cylinder installations
3.2 LOCATION OF LP GAS CYLINDERS
3.2.1 Restriction on location of cylinders
3.2.2 Required clearances around a cylinder
3.2.3 Mounting and stowage
3.2.4 Stowage of spare cylinders
3.2.5 Heat shield
3.3 CYLINDER ATTACHMENT
3.3.1 Restraints
3.3.2 Structures
3.4 CYLINDER COMPARTMENTS AND LP GAS LOCKERS
3.4.1 Caravans
3.4.2 Cylinders located in a combined storage compartment/locker for caravans
3.4.3 Boats
3.4.4 'Text deleted'
3.4.5 Access to cylinder compartments
3.4.6 Identification of cylinder compartment or LP Gas locker
SECTION 4 MEANS OF COMPLIANCE-GAS PRESSURE REGULATORS
4.1 SUITABILITY OF PRESSURE REGULATORS
4.2 OUTLET PRESSURE
4.3 MOUNTING AND SUPPORT OF REGULATOR
SECTION 5 MEANS OF COMPLIANCE-PIPING AND FITTINGS
5.1 GENERAL
5.1.1 Location
5.1.2 Size
5.1.3 Construction
5.1.4 Piping specification
5.1.5 Cylinder connections
5.2 INSTALLATION OF PIPING
5.2.1 General requirements
5.2.2 Piping in caravans
5.2.3 Piping in boats
5.2.4 Rigid piping
5.2.5 Hose assemblies
5.2.6 Prohibition on earthing of piping
5.2.7 Isolation valves
5.2.8 Quick-connect devices
5.2.9 Jointing compounds and materials
5.2.10 Pipe supports and fixings
5.2.11 Sealing of open ends
SECTION 6 MEANS OF COMPLIANCE-GAS APPLIANCES
6.1 PROHIBITED APPLIANCES
6.2 RESTRICTION FOR STOWED APPLIANCES
6.3 FLAME SAFEGUARD SYSTEM
6.4 MANUFACTURER'S INSTRUCTIONS
6.5 CLEARANCES
6.6 DISTANCE FROM SOURCES OF FUEL
6.7 RESTRICTION ON INSTALLATION OF AN APPLIANCE ON A PETROL-FUELLED BOAT
6.8 ELECTRICAL REQUIREMENTS
6.8.1 General
6.8.2 For Australian use only
6.9 SPACE HEATERS
6.10 COOKING APPLIANCES
6.10.1 Clearances around gas cooking appliances
6.10.2 Protection of a combustible surface near a gas cooking appliance
6.10.3 Vapour seal
6.10.4 Warning labels for cooking appliances
6.10.5 Cooking appliances on boats
6.11 REFRIGERATORS
6.11.1 Flues
6.11.2 Vents
6.11.3 Clearances
6.11.4 Ventilation
6.12 INSTANTANEOUS WATER HEATERS
6.13 SPA POOL HEATERS ON BOATS
6.13.1 Prohibited locations
6.13.2 Supporting base
6.13.3 Control systems
6.13.4 Requirement for pool heater where flow and return water pipes are of plastic
6.13.5 Non-return valve required
6.13.6 Restriction on fitting of a valve in water flow line
6.14 GAS BARBECUES AND RADIANT GAS HEATERS FOR OUTDOOR USE
SECTION 7 MEANS OF COMPLIANCE-VENTILATION
7.1 GENERAL
7.2 APPROPRIATE VENTILATION SYSTEMS
7.3 VENTILATION OPENINGS-CARAVANS AND BOATS
7.3.1 Minimum free area
7.3.2 Special requirements for camper trailers and boats
7.3.3 Special requirements for RVs (motorized caravans)
7.4 POSITION OF OPENINGS-CARAVANS ONLY
7.4.1 Cross ventilation
7.4.2 Distance from ceiling
7.4.3 Distance from floor
7.4.4 Vent warning label
7.5 POSITION OF OPENINGS-BOATS ONLY
7.6 GAS DETECTION SYSTEM REQUIRED-BOATS ONLY
SECTION 8 MEANS OF COMPLIANCE-FLUEING
8.1 FLUE CONSTRUCTION AND CLEARANCES
8.2 PROTECTION FROM ENVIRONMENTAL EFFECTS
8.3 DISTURBANCES
8.4 LOCATION OF FLUE TERMINAL
8.4.1 General
8.4.2 Termination of a flue under a cover
8.5 FLUE MATERIALS
8.6 PROPRIETARY FLUEING SYSTEMS
SECTION 9 MEANS OF COMPLIANCE-TESTING AND COMMISSIONING
9.1 TESTING FOR GASTIGHTNESS
9.2 COMMISSIONING
9.2.1 Commissioning of appliance
9.2.2 Other commissioning checks
SECTION 10 COMPLIANCE, MARKINGS AND LABELS
10.1 GAS COMPLIANCE PLATE
10.2 LABELS AND MARKINGS ADJACENT TO GAS CYLINDERS
10.3 LABELS AND MARKINGS NEAR GAS APPLIANCES
10.3.1 General
10.3.2 Additional marking for boats
APPENDIX A - NORMATIVE REFERENCES
APPENDIX B - CONVERSION FACTORS
APPENDIX C - FIRE RESISTANT MATERIAL
C1 GENERAL
C2 SPECIFICATION FOR FIRE RESISTANT MATERIAL
C3 EXAMPLES TO DETERMINE REQUIRED THICKNESS OF FIRE RESISTANT MATERIAL
C4 ACCEPTABLE METHODS OF PROTECTION
APPENDIX D - PIPE SIZING
D1 INTRODUCTION
D1.1 General
D1.2 Pipe conditions
D1.3 Fitting allowance
D1.4 Equations used
D1.5 Excessive gas velocities
D2 NEW PIPING SYSTEMS
D3 EXISTING PIPING SYSTEMS
D4 INFORMATION REQUIRED
D5 DESIGN PROCEDURE USING PIPE SIZING GRAPHS
D5.1 Introduction
D5.2 Sketch the piping layout
D5.3 Tabulate the pipe runs
D5.4 Determine the length of the longest pipe run
D5.5 Determine the allowable pressure drop per metre
D5.6 Determine the required pipe size from the pipe sizing graphs
D5.7 Pipe sizing graphs
D6 DESIGN PROCEDURE USING PIPE SIZING TABLES
D6.1 General
D6.2 Sketch the piping layout
D6.3 Determine the main run
D6.4 Select the piping material
D6.5 Tabulate the pipe runs
D6.6 Selecting the pipe size
D6.7 Pipe sizing tables
APPENDIX E - COMBUSTIBLE GAS DETECTION SYSTEMS FOR BOATS
E1 GENERAL
E2 GAS DETECTION SYSTEM
E3 INSTALLATION OF THE SYSTEM
E3.1 Solenoid valve
E3.2 Position of audible alarm
E3.3 Sensors
E3.4 Operation of the system when gas is detected
APPENDIX F - TESTING GAS INSTALLATIONS
F1 GENERAL
F1.1 New installations
F1.2 Additions and alterations to installations
F2 PIPEWORK TEST
F2.1 Method
F2.2 Test result
F3 INSTALLATION GAS TIGHTNESS TEST
F3.1 General
F3.2 Method 1-Pressure loss
F3.3 Method 2-Using bubble leakage detector
F4 METHODS OF LOCATING GAS LEAKS
APPENDIX G - CONSUMER INSTRUCTIONS
APPENDIX H - METHOD OF LOCATING GAS PRESSURE REGULATORS
APPENDIX I - GUIDELINES FOR GAS APPLIANCE COMMISSIONING
I1 GENERAL
I2 STOVES, COOKERS AND HOT PLATES
I3 INSTANTANEOUS WATER HEATERS
I4 STORAGE WATER HEATERS
APPENDIX J - SYMBOLS USED IN GAS CONTROL SYSTEM DIAGRAMS
APPENDIX K - GAS INSTALLATION CHECKLIST
APPENDIX L - APPLIANCES IN OUTDOOR AREAS
L1 DIAGRAMMATIC REPRESENTATION OF OUTDOOR AREAS
L2 DOMESTIC GAS BARBECUES AND RADIANT GAS HEATERS
BIBLIOGRAPHY
AS/NZS 5601.2:2013
Online Library subscription information
Online library subscriptions provide a cost-effective solution for organisations of any size to access the latest standards, offering 24/7 access to a personalised catalogue. The service ensures subscribers have have the most up-to-date version of selected standards, incluing automatic updates for any amendments or versions. Pricing is dependent on the chosen standards and the number of concurrent users, with discounts applied from the standards PDF price. For customised subscriptions or further inquiries, contact the Online Library team.