ISO 7452:2013
Hot-rolled steel plates — Tolerances on dimensions and shape
ISO 7452:2013 specifies requirements for tolerances for hot-rolled steel plates made on a reversing mill with the following characteristics:
- nominal thickness: 3 mm ≤ t ≤ 400 mm;
- nominal width: w ≥ 600 mm.
ISO 7452:2013 does not apply to stainless steel.
ISO 7452:2013 does not include continuous mill products, custom-made plate, checker plate or bulb plate for flooring or wide flats.
| Get this standard | Prices exclude GST | |
|---|---|---|
| PDF ( Single user document) |
$179.13 NZD
|
|
| HardCopy |
$214.78 NZD
|
|
| Networkable PDF |
Price varies
|
Section sec_1
Section sec_2
Section sec_3
Section sec_4
Section sec_4.1
Section sec_4.2
Section sec_5
Section sec_5.1
Section sec_5.2
Section sec_6
Section sec_6.1
Section sec_6.2
Section sec_6.3
Section sec_7
Section sec_7.1
Section sec_7.2
Table tab_a
Figure fig_1
Section sec_8
Section sec_8.1
Section sec_8.2
Section sec_8.3
Section sec_8.4
Section sec_8.5
Section sec_8.6
Table tab_b
Figure fig_2
Section sec_8.7
Annex sec_A
Annex sec_A.1
Table tab_A.1
Annex sec_A.2
Table tab_A.2
Annex sec_A.3
Table tab_A.3
Annex sec_A.4
Table tab_A.4
Annex sec_A.5
Table tab_A.5
Annex sec_B
Annex sec_B.1
Table tab_B.1
Annex sec_B.2
Annex sec_B.3
Table tab_B.3
Annex sec_B.4
Table tab_B.4
Annex sec_B.5
Table tab_B.5
Reference ref_1
Reference ref_2
Reference ref_3
Reference ref_4
Reference ref_5
Reference ref_6
Reference ref_7
Reference ref_8
Reference ref_9
Reference ref_10
Reference ref_11
Reference ref_12
Reference ref_13
Reference ref_14
Reference ref_15
Reference ref_16
Reference ref_17
Reference ref_18
Reference ref_19
Table tab_B.2
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Information to be supplied by the purchaser
4.1 General
4.2 Options
5 Form of supply
5.1 Selection of tolerances, edge camber and out-of-squareness
5.2 Absence of information
6 Tolerances and dimensions
6.1 Thickness
6.2 Width
6.3 Length
7 Tolerances on shape
7.1 Edge camber and out-of-squareness
7.2 Flatness
8 Measurements
8.1 General
8.2 Thickness
8.3 Width
8.4 Length
8.5 Edge camber
8.6 Out-of-squareness
8.7 Flatness
Annex A (normative) Tolerance values
Annex B (normative) Additional tolerance values
Bibliography
Previous versions
Keep me up-to-date
Sign up to receive updates when there are changes to this standard
Related Information
Similar Standards
-
AS/NZS 1163:2016
Cold-formed structural steel hollow sections -
AS/NZS 1163:2016 A1
Cold-formed structural steel hollow sections: Amendment 1:2017 -
AS/NZS 1365:1996
Tolerances for flat-rolled steel products
-
AS/NZS 1365:1996A1
Tolerances for flat-rolled steel products: Amendment 1
Section sec_1
Section sec_2
Section sec_3
Section sec_4
Section sec_4.1
Section sec_4.2
Section sec_5
Section sec_5.1
Section sec_5.2
Section sec_6
Section sec_6.1
Section sec_6.2
Section sec_6.3
Section sec_7
Section sec_7.1
Section sec_7.2
Table tab_a
Figure fig_1
Section sec_8
Section sec_8.1
Section sec_8.2
Section sec_8.3
Section sec_8.4
Section sec_8.5
Section sec_8.6
Table tab_b
Figure fig_2
Section sec_8.7
Annex sec_A
Annex sec_A.1
Table tab_A.1
Annex sec_A.2
Table tab_A.2
Annex sec_A.3
Table tab_A.3
Annex sec_A.4
Table tab_A.4
Annex sec_A.5
Table tab_A.5
Annex sec_B
Annex sec_B.1
Table tab_B.1
Annex sec_B.2
Annex sec_B.3
Table tab_B.3
Annex sec_B.4
Table tab_B.4
Annex sec_B.5
Table tab_B.5
Reference ref_1
Reference ref_2
Reference ref_3
Reference ref_4
Reference ref_5
Reference ref_6
Reference ref_7
Reference ref_8
Reference ref_9
Reference ref_10
Reference ref_11
Reference ref_12
Reference ref_13
Reference ref_14
Reference ref_15
Reference ref_16
Reference ref_17
Reference ref_18
Reference ref_19
Table tab_B.2
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Information to be supplied by the purchaser
4.1 General
4.2 Options
5 Form of supply
5.1 Selection of tolerances, edge camber and out-of-squareness
5.2 Absence of information
6 Tolerances and dimensions
6.1 Thickness
6.2 Width
6.3 Length
7 Tolerances on shape
7.1 Edge camber and out-of-squareness
7.2 Flatness
8 Measurements
8.1 General
8.2 Thickness
8.3 Width
8.4 Length
8.5 Edge camber
8.6 Out-of-squareness
8.7 Flatness
Annex A (normative) Tolerance values
Annex B (normative) Additional tolerance values
Bibliography