ISO 15630-1:2010
Steel for the reinforcement and prestressing of concrete — Test methods — Part 1: Reinforcing bars, wire rod and wire
ISO 15630-1:2010 specifies test methods applicable to reinforcing bars, wire rod and wire for concrete.
| Get this standard | Prices exclude GST | |
|---|---|---|
| PDF ( Single user document) |
$118.26 NZD
|
|
| HardCopy |
$152.17 NZD
|
|
| Networkable PDF |
Price varies
|
Scope
Normative references
Symbols
General provisions concerning test pieces
Tensile test
Test piece
Test equipment
Test procedure
Bend test
Test piece
Test equipment
Test procedure
Interpretation of test results
Rebend test
Test piece
Test equipment
Bending device
Rebending device
Test procedure
General
Bending
Artificial ageing
Rebending
Interpretation of test results
Axial force fatigue test
Principle of test
Test piece
Test equipment
Test procedure
Provisions concerning the test piece
Upper force (Fup) and force range (Fr)
Stability of force and frequency
Counting of force cycles
Frequency
Temperature
Validity of the test
Chemical analysis
Measurement of the geometrical characteristics
Test piece
Test equipment
Test procedure
Heights of transverse ribs or depths of indentations
Maximum value (amax)
Value at a given position
Height of longitudinal ribs (a()
Transverse rib or indentation spacing (c)
Pitch (P)
Part of the circumference without ribs or indentations ((ei)
Transverse rib or indentation angle (()
Transverse rib flank inclination (()
Width of transverse rib or width of indentation (b)
Determination of the relative rib or indentation area (fR or
Introduction
Measurements
Calculation of fR
Relative rib area
Simplified formulae
Formula used for the calculation of fR
Calculation of fP
Relative indentation area
Simplified formulae
Formula used for the calculation of fP
Determination of deviation from nominal mass per metre
Test piece
Accuracy of measurement
Test procedure
Test report
Previous versions
Keep me up-to-date
Sign up to receive updates when there are changes to this standard
Related Information
Similar Standards
-
AS/NZS 4672.1:2007
Steel prestressing materials - General requirements
-
AS/NZS 4672.2:2007
Steel prestressing materials - Testing requirements
-
BS 4449:2005+A3:2016
Steel for the reinforcement of concrete. Weldable reinforcing steel. Bar, coil and decoiled product. Specification
-
BS 4482:2005
Steel wire for the reinforcement of concrete products. Specification
Scope
Normative references
Symbols
General provisions concerning test pieces
Tensile test
Test piece
Test equipment
Test procedure
Bend test
Test piece
Test equipment
Test procedure
Interpretation of test results
Rebend test
Test piece
Test equipment
Bending device
Rebending device
Test procedure
General
Bending
Artificial ageing
Rebending
Interpretation of test results
Axial force fatigue test
Principle of test
Test piece
Test equipment
Test procedure
Provisions concerning the test piece
Upper force (Fup) and force range (Fr)
Stability of force and frequency
Counting of force cycles
Frequency
Temperature
Validity of the test
Chemical analysis
Measurement of the geometrical characteristics
Test piece
Test equipment
Test procedure
Heights of transverse ribs or depths of indentations
Maximum value (amax)
Value at a given position
Height of longitudinal ribs (a()
Transverse rib or indentation spacing (c)
Pitch (P)
Part of the circumference without ribs or indentations ((ei)
Transverse rib or indentation angle (()
Transverse rib flank inclination (()
Width of transverse rib or width of indentation (b)
Determination of the relative rib or indentation area (fR or
Introduction
Measurements
Calculation of fR
Relative rib area
Simplified formulae
Formula used for the calculation of fR
Calculation of fP
Relative indentation area
Simplified formulae
Formula used for the calculation of fP
Determination of deviation from nominal mass per metre
Test piece
Accuracy of measurement
Test procedure
Test report