ISO 3302-1:2014
Rubber — Tolerances for products — Part 1: Dimensional tolerances
ISO 3302-1:2014 specifies classes of dimensional tolerances and their values for moulded, extruded, and calendared solid rubber products. The relevant test methods necessary for the establishment of compliance with ISO 3302-1:2014 are also specified.
The tolerances are primarily intended for use with vulcanized rubber but can also be suitable for products made of thermoplastic rubbers.
ISO 3302-1:2014 does not apply to precision toroidal sealing rings or to calendared composite products such as rubber-coated fabrics or products where a rubber coating is applied by the process of topping or skim coating.
| Get this standard | Prices exclude GST | |
|---|---|---|
| PDF ( Single user document) |
$118.26 NZD
|
|
| Networkable PDF |
Price varies
|
Section sec_1
Section sec_2
Section sec_3
Section sec_3.1
Section sec_3.2
Section sec_3.2.1
Section sec_3.2.1.1
Section sec_3.2.1.2
Section sec_3.2.1.3
Section sec_3.2.1.4
Section sec_3.2.2
Section sec_3.2.3
Section sec_4
Section sec_5
Section sec_5.1
Section sec_5.2
Section sec_5.3
Section sec_5.3.1
Section sec_5.3.2
Section sec_5.4
Table tab_a
Figure fig_1
Table tab_1
Section sec_5.5
Table tab_2
Section sec_6
Section sec_6.1
Section sec_6.2
Section sec_6.3
Section sec_6.3.1
Section sec_6.3.2
Table tab_3
Section sec_6.3.3
Table tab_4
Section sec_6.3.4
Section sec_6.3.4.1
Table tab_5
Section sec_6.3.4.2
Table tab_6
Section sec_6.3.5
Table tab_7
Section sec_6.3.6
Table tab_8
Section sec_7
Section sec_7.1
Section sec_7.2
Section sec_7.3
Table tab_9
Table tab_10
Foreword
Introduction
1 Scope
2 Normative references
3 Measurement of dimensions
3.1 General
3.2 Test instruments
4 Tolerances
5 Mouldings
5.1 General
5.2 Classification
5.3 Fixed dimensions and closure dimensions
5.4 Tolerances
5.5 Flash
6 Extrusions
6.1 General
6.2 Classification
6.3 Tolerances
7 Calendered sheet
7.1 General
7.2 Classification
7.3 Tolerances
Previous versions
Keep me up-to-date
Sign up to receive updates when there are changes to this standard
Related Information
Similar Standards
-
BS 3379:1975
Specification for flexible urethane foam for loadbearing applications
-
BS 3379:2005+A1:2011
Combustion modified flexible polyurethane cellular materials for loadbearing applications. Specification
-
BS 6206:1981
Specification for impact performance requirements for flat safety glass and safety plastics for use in buildings
-
BS EN 1778:2000
Characteristic values for welded thermoplastics constructions. Determination of allowable stresses and moduli for design of thermoplastics equipment
Section sec_1
Section sec_2
Section sec_3
Section sec_3.1
Section sec_3.2
Section sec_3.2.1
Section sec_3.2.1.1
Section sec_3.2.1.2
Section sec_3.2.1.3
Section sec_3.2.1.4
Section sec_3.2.2
Section sec_3.2.3
Section sec_4
Section sec_5
Section sec_5.1
Section sec_5.2
Section sec_5.3
Section sec_5.3.1
Section sec_5.3.2
Section sec_5.4
Table tab_a
Figure fig_1
Table tab_1
Section sec_5.5
Table tab_2
Section sec_6
Section sec_6.1
Section sec_6.2
Section sec_6.3
Section sec_6.3.1
Section sec_6.3.2
Table tab_3
Section sec_6.3.3
Table tab_4
Section sec_6.3.4
Section sec_6.3.4.1
Table tab_5
Section sec_6.3.4.2
Table tab_6
Section sec_6.3.5
Table tab_7
Section sec_6.3.6
Table tab_8
Section sec_7
Section sec_7.1
Section sec_7.2
Section sec_7.3
Table tab_9
Table tab_10
Foreword
Introduction
1 Scope
2 Normative references
3 Measurement of dimensions
3.1 General
3.2 Test instruments
4 Tolerances
5 Mouldings
5.1 General
5.2 Classification
5.3 Fixed dimensions and closure dimensions
5.4 Tolerances
5.5 Flash
6 Extrusions
6.1 General
6.2 Classification
6.3 Tolerances
7 Calendered sheet
7.1 General
7.2 Classification
7.3 Tolerances