AS/NZS 1200:2015
Pressure equipment
Covers the design, materials, manufacture, examination, testing, installation, conformity assessment, commissioning, operation, inspection, maintenance, repair, alteration and disposal of pressure equipment (boilers, pressure vessels and pressure piping), but excludes gas cylinders and other equipment as set out in Appendix A.
| Get this standard | Prices exclude GST | |
|---|---|---|
| PDF ( Single user document) |
$147.60 NZD
|
|
| HardCopy |
$164.00 NZD
|
|
| Networkable PDF |
Price varies
|
|
| Online Library ( Annual subscription) |
Info
Price varies
Online Library subscription information Online library subscriptions provide a cost-effective solution for organisations of any size to access the latest standards, offering 24/7 access to a personalised catalogue. The service ensures subscribers have have the most up-to-date version of selected standards, incluing automatic updates for any amendments or versions. Pricing is dependent on the chosen standards and the number of concurrent users, with discounts applied from the standards PDF price. For customised subscriptions or further inquiries, contact the Online Library team. |
PREFACE
CONTENTS
SECTION 1 SCOPE AND GENERAL
1.1 SCOPE
1.2 OBJECTIVE
1.3 APPLICATION
1.4 DEFINITIONS
1.5 REFERENCED DOCUMENTS
1.6 NEW DESIGNS, MATERIALS AND MANUFACTURING METHODS
1.7 ROUNDING OF NUMERICAL VALUES
1.8 CONVERSION OF UNITS
1.9 TOLERANCES
1.10 CONCESSIONS
1.11 NEW ZEALAND REQUIREMENTS
SECTION 2 BASIC REQUIREMENTS AND COMPLIANCE STANDARDS
2.1 BASIC REQUIREMENTS
2.2 COMPLIANCE STANDARDS
2.3 MIXING STANDARDS
APPENDIX A - EQUIPMENT COVERED BY THIS STANDARD
A1 PRESSURE EQUIPMENT COVERED
A2 EXAMPLES
A3 EQUIPMENT OR PLANT UNDER PRESSURE NOT SPECIFICALLY COVERED
APPENDIX B - DEFINITIONS
B1 GENERAL
B2 DEFINITIONS
B2.1 Alter
B2.2 Boiler
B2.3 Commissioning
B2.4 Competent person
B2.5 Conformity assessment
B2.6 Designer
B2.7 Equivalent
B2.8 Fired heater
B2.9 Gas cylinder
B2.10 Hazard
B2.11 Hot water boiler (New Zealand)
B2.12 Inspection
B2.13 Installer
B2.14 LP gas fuel vessel for automotive use
B2.15 Maintain
B2.16 Manufacturer
B2.17 May
B2.18 Nationally recognized
B2.19 Operate
B2.20 Owner
B2.21 Parties concerned
B2.22 Practicable
B2.23 Pressures
B2.24 Pressure equipment
B2.25 Pressure piping
B2.26 Pressure vessel
B2.27 Purchaser
B2.28 Regulator
B2.29 Repair
B2.30 Risk
B2.31 Risk assessment
B2.32 Safety requirements
B2.33 Serially produced pressure vessels
B2.34 Shall
B2.35 Should
B2.36 Supplier
B2.37 User
APPENDIX C - LIST OF REFERENCED DOCUMENTS
APPENDIX D - MATERIALS FOR USE UNDER THIS STANDARD
D1 POLICY FOR MATERIALS
D1.1 General
D1.2 Permitted material Standards
D1.3 Alternative national Standards
D2 NEW MATERIAL
D2.1 Amendment or Supplement
D2.2 Mechanical properties
D2.3 Weldability
D2.4 Physical changes
APPENDIX E - NOT ALLOCATED
APPENDIX F - COMPARISON OF PRESSURE EQUIPMENT STANDARDS
F1 INTRODUCTION
F2 PURPOSE
F3 RECOGNIZED STANDARDS
F4 COMPARISON OF AUSTRALIAN AND OVERSEAS PRESSURE EQUIPMENT STANDARDS
F5 BOILER STANDARDS
F6 PRESSURE PIPING STANDARDS
F7 RELATED PRESSURE EQUIPMENT STANDARDS
F8 OBSERVATIONS/RECOMMENDATIONS
APPENDIX G - AUSTRALIAN PRESSURE EQUIPMENT PRACTICE
G1 GENERAL
APPENDIX H - NEW ZEALAND REQUIREMENTS
H1 GENERAL
H2 SPECIFIC REQUIREMENTS
H2.1 Design verification
H2.2 Fabrication inspection
H2.3 Certificate of inspection
H3 SEISMIC LOADINGS
APPENDIX I - THE USE OF EQUIVALENT STANDARDS
I1 GENERAL
I2 BASIS FOR USE
APPENDIX J - SAFETY REQUIREMENTS
J1 GENERAL
J2 GENERAL REQUIREMENTS
J2.1 Design and manufacture
J2.2 Use
J3 DESIGN
J3.1 General
J3.2 Design for adequate strength and deflection control
J3.3 Design for safe handling and operation
J3.4 Means of examination
J3.5 Means of isolation, draining and venting
J3.6 Corrosion or other chemical attack
J3.7 Wear
J3.8 Provisions for filling and discharge
J3.9 Protection against exceeding allowable limits
J3.10 Safety accessories
J3.11 External fire
J4 MANUFACTURE
J4.1 Manufacturing procedures
J4.2 Final assessment
J4.3 Marking and labelling
J4.4 Operating instructions
J5 MATERIALS
J5.1 General
J5.2 Materials for pressurized parts
J5.3 Documentation
J5.4 Compliance
J6 SAFETY REQUIREMENTS FOR SPECIAL APPLICATIONS
J6.1 Fired or otherwise heated pressure equipment with a risk of overheating
J6.2 Additional safety requirements for piping
J7 SPECIFIC QUANTITATIVE REQUIREMENTS FOR CERTAIN PRESSURE EQUIPMENT
J7.1 Provisions
J7.2 Allowable stresses
J7.3 Joint coefficients
J7.4 Pressure limiting device
J7.5 Hydrostatic test
J7.6 Material characteristics (for steel only)
J8 USE
J8.1 General
J8.2 Equipment operations
J8.3 Safety management system
Previous versions
Keep me up-to-date
Sign up to receive updates when there are changes to this standard
References
Pressure equipment - Welding and brazing qualification
Pressure equipment - Competencies of inspectors
Household and similar electrical appliances - Safety - Part 2.21: Particular requirements for storage water heaters
Household and similar electrical appliances - Safety - Part 2.35: Particular requirements for instantaneous water heaters
Code of practice for the installation, operation and maintenance of building service and small industrial boilers
Transportation containers for hazardous substances - Specification for small packages for transportation by land, sea and air
Related Information
Similar Standards
-
AS/NZS 3707:2001
Method for testing pressure cycling resistance of pipes and fittings
-
AS/NZS 3788:2006
Pressure equipment - In-service inspection
-
AS/NZS 3992:2015
Pressure equipment - Welding and brazing qualification -
AS/NZS 4130:2018
Polyethylene (PE) pipes for pressure applications
PREFACE
CONTENTS
SECTION 1 SCOPE AND GENERAL
1.1 SCOPE
1.2 OBJECTIVE
1.3 APPLICATION
1.4 DEFINITIONS
1.5 REFERENCED DOCUMENTS
1.6 NEW DESIGNS, MATERIALS AND MANUFACTURING METHODS
1.7 ROUNDING OF NUMERICAL VALUES
1.8 CONVERSION OF UNITS
1.9 TOLERANCES
1.10 CONCESSIONS
1.11 NEW ZEALAND REQUIREMENTS
SECTION 2 BASIC REQUIREMENTS AND COMPLIANCE STANDARDS
2.1 BASIC REQUIREMENTS
2.2 COMPLIANCE STANDARDS
2.3 MIXING STANDARDS
APPENDIX A - EQUIPMENT COVERED BY THIS STANDARD
A1 PRESSURE EQUIPMENT COVERED
A2 EXAMPLES
A3 EQUIPMENT OR PLANT UNDER PRESSURE NOT SPECIFICALLY COVERED
APPENDIX B - DEFINITIONS
B1 GENERAL
B2 DEFINITIONS
B2.1 Alter
B2.2 Boiler
B2.3 Commissioning
B2.4 Competent person
B2.5 Conformity assessment
B2.6 Designer
B2.7 Equivalent
B2.8 Fired heater
B2.9 Gas cylinder
B2.10 Hazard
B2.11 Hot water boiler (New Zealand)
B2.12 Inspection
B2.13 Installer
B2.14 LP gas fuel vessel for automotive use
B2.15 Maintain
B2.16 Manufacturer
B2.17 May
B2.18 Nationally recognized
B2.19 Operate
B2.20 Owner
B2.21 Parties concerned
B2.22 Practicable
B2.23 Pressures
B2.24 Pressure equipment
B2.25 Pressure piping
B2.26 Pressure vessel
B2.27 Purchaser
B2.28 Regulator
B2.29 Repair
B2.30 Risk
B2.31 Risk assessment
B2.32 Safety requirements
B2.33 Serially produced pressure vessels
B2.34 Shall
B2.35 Should
B2.36 Supplier
B2.37 User
APPENDIX C - LIST OF REFERENCED DOCUMENTS
APPENDIX D - MATERIALS FOR USE UNDER THIS STANDARD
D1 POLICY FOR MATERIALS
D1.1 General
D1.2 Permitted material Standards
D1.3 Alternative national Standards
D2 NEW MATERIAL
D2.1 Amendment or Supplement
D2.2 Mechanical properties
D2.3 Weldability
D2.4 Physical changes
APPENDIX E - NOT ALLOCATED
APPENDIX F - COMPARISON OF PRESSURE EQUIPMENT STANDARDS
F1 INTRODUCTION
F2 PURPOSE
F3 RECOGNIZED STANDARDS
F4 COMPARISON OF AUSTRALIAN AND OVERSEAS PRESSURE EQUIPMENT STANDARDS
F5 BOILER STANDARDS
F6 PRESSURE PIPING STANDARDS
F7 RELATED PRESSURE EQUIPMENT STANDARDS
F8 OBSERVATIONS/RECOMMENDATIONS
APPENDIX G - AUSTRALIAN PRESSURE EQUIPMENT PRACTICE
G1 GENERAL
APPENDIX H - NEW ZEALAND REQUIREMENTS
H1 GENERAL
H2 SPECIFIC REQUIREMENTS
H2.1 Design verification
H2.2 Fabrication inspection
H2.3 Certificate of inspection
H3 SEISMIC LOADINGS
APPENDIX I - THE USE OF EQUIVALENT STANDARDS
I1 GENERAL
I2 BASIS FOR USE
APPENDIX J - SAFETY REQUIREMENTS
J1 GENERAL
J2 GENERAL REQUIREMENTS
J2.1 Design and manufacture
J2.2 Use
J3 DESIGN
J3.1 General
J3.2 Design for adequate strength and deflection control
J3.3 Design for safe handling and operation
J3.4 Means of examination
J3.5 Means of isolation, draining and venting
J3.6 Corrosion or other chemical attack
J3.7 Wear
J3.8 Provisions for filling and discharge
J3.9 Protection against exceeding allowable limits
J3.10 Safety accessories
J3.11 External fire
J4 MANUFACTURE
J4.1 Manufacturing procedures
J4.2 Final assessment
J4.3 Marking and labelling
J4.4 Operating instructions
J5 MATERIALS
J5.1 General
J5.2 Materials for pressurized parts
J5.3 Documentation
J5.4 Compliance
J6 SAFETY REQUIREMENTS FOR SPECIAL APPLICATIONS
J6.1 Fired or otherwise heated pressure equipment with a risk of overheating
J6.2 Additional safety requirements for piping
J7 SPECIFIC QUANTITATIVE REQUIREMENTS FOR CERTAIN PRESSURE EQUIPMENT
J7.1 Provisions
J7.2 Allowable stresses
J7.3 Joint coefficients
J7.4 Pressure limiting device
J7.5 Hydrostatic test
J7.6 Material characteristics (for steel only)
J8 USE
J8.1 General
J8.2 Equipment operations
J8.3 Safety management system
Previous versions
AS/NZS 1200:2015
Online Library subscription information
Online library subscriptions provide a cost-effective solution for organisations of any size to access the latest standards, offering 24/7 access to a personalised catalogue. The service ensures subscribers have have the most up-to-date version of selected standards, incluing automatic updates for any amendments or versions. Pricing is dependent on the chosen standards and the number of concurrent users, with discounts applied from the standards PDF price. For customised subscriptions or further inquiries, contact the Online Library team.